Dual Canopy Mechanic Electrical Engineering Co., Ltd. is one of the leading manufacturers and suppliers of primary current injection in China. Please feel free to wholesale discount products for sale here and get quotation from our factory. Customized orders are welcome.
Why This Primary Current Injection Equipment Exists?

A Primary Current Injection Test Set is the only method that verifies the entire protection chain-from the primary current transformer winding through the relay logic, wiring, trip circuit, and finally to the breaker contacts-under real load conditions. Unlike secondary injection, which only tests the relay electronics, primary injection simulates actual fault currents (hundreds to thousands of amperes) so wholesale buyers, utilities, and commissioning teams can confirm that every component responds correctly when it matters.
Our design philosophy is simple: high accuracy must not mean low portability. Every unit is engineered with an auto-coupled voltage regulator, a true-RMS digital ammeter, and thermal overload protection so that field technicians can run continuous tests safely without compromising measurement integrity.
What does the procurement reference data include?
Input AC 50Hz, 220V.
Output single-phase 0-100A (200A, 500A, 1000A, 2000A, 3000A, 4000A, 5000A) AC current; the current can be adjusted smoothly and continuously, with an accuracy higher than 0.1 level;
The output current is a standard sine wave with small burrs, which is better than the power system requirement index standard, and the ripple factor is less than 0.3%.
Output current mode: true effective value is continuously adjustable;
Output waveform: standard sine wave;
Output opening voltage: 5V.
Current accuracy: each current can be adjusted smoothly and continuously, with an accuracy higher than 0.5 level. The current and voltage meter display is true effective value, with high accuracy and high stability; current stability: 0.1%; current waveform distortion: THD 1%;
Protection settings: overcurrent, overvoltage; the current action time of the measured component can be measured, and the locking action time can be recorded synchronously.
Normally open and normally closed contacts are automatically distinguished.
Time measurement range: 0.0001S---9999.9999S,
Accuracy: 0.0001S
Power: 3000VA (5000VA, 18KVA)

Why These Features Matter?
We use a toroidal current transformer with precision-wound copper rather than a simple shunt because toroidal CTs provide linear response up to 3,000 A with minimal phase shift-critical when verifying relay timing. The digital timer captures trip times in under 20 ms because breaker trip curves (per manufacturer data from Schneider, ABB, Siemens) require millisecond-level resolution to detect calibration drift. Thermal overload circuits are calibrated to IEC 61010-1 because continuous high-current operation generates significant I²R heat; without automatic trip, insulation degradation accelerates by up to 40% over 500 hours.
Where Wholesale Buyers Deploy This?
Substation Commissioning & Maintenance
Used to prove CT polarity, verify relay trip settings, and confirm breaker contact resistance under load. Essential before energizing new 11 kV / 33 kV / 66 kV installations. Wholesale buyers in the Middle East and Southeast Asia typically order 500A–2000A portable units with 5-minute duty cycles for on-site maintenance contracts.
Circuit Breaker Factory Acceptance (FAT)
OEM manufacturers and large electrical contractors use high-capacity sets (up to 7,000 A) to perform thermal-run and instantaneous-trip tests against manufacturer curves. Our 20 kVA loading units meet the 10× rated current requirement specified by ABB and Schneider for thermal-magnetic trip verification.
Current Transformer Ratio & Polarity Verification
Inject a known primary current and compare the secondary output. A ±0.5% accuracy reading is required to detect ratio errors as small as 0.5%, which is the threshold where protection relay mis-coordination begins.
Railway & Energy Storage Systems
Rail operators use portable sets for 25 Hz / 60 Hz testing of traction circuit breakers. Energy storage (BESS) integrators require precise DC injection capability for battery protection relay validation. Our systems support 15 Hz to 400 Hz frequency adjustment.
What does a "Professional Description for Technical Buyers" entail?
1. High-Output Capacity: 0 – 3,000 A (Up to 20 kVA)
Why it exists: Breaker trip curves require testing at 1.5× to 10× rated current. A 2,000 A breaker needs 20,000 A for instantaneous verification; our modular loading units scale from 200 A / 1 kVA to 3,000 A / 20 kVA so wholesale buyers can stock one platform with interchangeable modules.
Data point: Per IEC 60255-151, protection relay accuracy must be verified at 120% of rated current. Our set maintains ±0.5% full-scale accuracy at 120% overload for up to 5 minutes.
2. True-RMS Digital Measurement (±0.5% to ±1%)
Why it exists: Non-sinusoidal fault currents (caused by harmonics from VFD loads) distort average-responding meters. True-RMS ensures the relay sees the same RMS value the meter records. Our 4½-digit LED / LCD display updates at 10 Hz for real-time observation.
Data point: Independent calibration reports per ISO/IEC 17025 show deviation under ±0.3% at 1,000 A, 50 Hz, 25 °C ambient.
3. Auto-Coupled Voltage Regulator + Fine-Tune Control
Why it exists: Manual rheostats introduce contact resistance drift. The auto-coupled regulator uses a motorized tap changer with silver-copper contacts rated for 10,000 cycles, reducing voltage ripple to <1% and ensuring stable current injection even during long-duration thermal tests.
What are the key factors buyers consider when purchasing a primary current injection tester?
MOQ & Price Structure
Standard MOQ is 1 unit for trial orders; volume discounts apply at 5, 10, and 50 units. Our factory-direct pricing eliminates middle-margin layers.
Certification & Compliance
Every unit ships with an ISO 9001 factory audit report, a CE conformity declaration, and a calibration certificate traceable to national metrology standards. We reference IEC 61010-1 (safety) and IEC 60255-151 (relay testing) in design verification. Buyers requesting third-party witness testing can request reports from accredited labs before shipment.
Customization & OEM / ODM
Wholesale orders of 10+ units can request custom branding, multilingual LCD interfaces (English, Arabic, Spanish, Russian), modified voltage inputs (110 V, 220 V, 380 V), and private-label casing colors. Firmware customization-including custom test sequences and data-logging formats-is available for orders of 20+ units. Typical customization lead time: 15–25 working days.
Our address
Baoding Cloud Center, Hebei, China
Phone Number/whatsapp
+8613603329412
dylan@dualcanopy.com

FAQ
Q1: What is the difference between primary current injection and secondary current injection, and why does a wholesale buyer need both?
A: Primary injection applies high current directly through the primary circuit (CT primary, breaker, wiring, relay), verifying the entire protection chain including wiring polarity and breaker contact resistance. Secondary injection applies a low-level signal directly to the relay electronics, skipping the CT and breaker.
Q2: How do I select the correct output capacity (kVA) for my wholesale inventory or project?
A: Match the test set's current output to the highest-rated breaker in your target market, then multiply by 10 for instantaneous trip testing. Example: for 400 A breakers, you need 4,000 A capacity-select our 3,000 A / 20 kVA model or a modular 2,000 A system with overload capability. If your market focuses on low-voltage MCB testing (≤100 A), a 500 A / 3 kVA portable unit is sufficient. We provide a capacity-selection worksheet during pre-sales consultation.
Q3: What calibration interval is recommended?
A: We recommend annual calibration for units in frequent field use (more than 100 test cycles per month) and biennial calibration for occasional-use lab instruments. The calibration procedure requires a reference standard with ±0.2% accuracy, a stable 230 V supply, and a controlled 25 °C environment. Most accredited electrical calibration labs can perform it using our provided procedure document.
Hot Tags: primary current injection, China primary current injection manufacturers, suppliers, factory, ac hipot tester resonance test, Primary Current Injection Testing System, ac resonant test system 75kva
