Common Test Equipment And Selection Methods For AC Withstand Voltage Tests

Sep 24, 2025

Leave a message

Test equipment
The equipment used for AC withstand voltage tests usually includes test transformers, voltage regulating devices, overcurrent protection devices, voltage measurement devices, protection ball gaps, protection resistors, and control devices, among which the key equipment are the test transformers, voltage regulating devices, protection resistors, and voltage measurement devices.
When selecting a test transformer, the following two points should be considered:
a) Voltage. Select a test transformer with an appropriate voltage based on the test voltage of the tested item. When the test voltage is high, a multi-stage series-connected test transformer can be used. It is necessary to check whether the low-voltage side voltage required by the test transformer matches the on-site power supply voltage and the voltage regulator.
b) Current. The current is calculated by the formula: I = ωCxU
Where 1 - the current output by the high-voltage side of the test transformer, mA;
ω - angular frequency (2πf);
Cx - the capacitance of the tested item, μF;
U - the test voltage, kV.
The capacitance C can be obtained from measuring the capacitance of the tested item/tan8 or selected according to relevant test standards. Correspondingly, the required power supply capacity P (KVA) is calculated as:
P = ωCxU² x 10-3
During the test, the transformer capacity is selected based on the P value, and it is generally not allowed to operate under overload. When using a voltage transformer as the test power supply, it is allowed to overload by 3.5 to 5 times within 3 minutes.
AC withstand voltage test equipment
Voltage regulating device
The voltage regulating device should preferably use a self-coupled type. If the capacity is insufficient, a moving-arc type voltage regulating device can be used. The output waveform of the voltage regulating device should be close to a sine wave. To improve the voltage waveform, a filter composed of an inductor and a capacitor connected in series at the output end of the voltage regulating device can be used.
Common voltage regulating devices include self-coupled voltage regulating devices, moving-arc voltage regulating devices, contact voltage regulating devices, and induction voltage regulating devices. Due to the fact that the output voltage waveform of the moving-arc voltage regulating device has significant distortion within a certain range, moving-arc voltage regulating devices are not suitable for use in the field.
Self-coupled voltage regulating device
A self-coupled voltage regulating device uses carbon brushes for contact regulation, so its capacity is limited and is suitable for small-capacity voltage regulation of 500V and below. The capacity of the voltage regulating device is selected as follows:
P = (0.75 - 1)P
Where Po - the capacity of the self-coupled voltage regulating device;
P - the capacity of the test transformer.
Contact voltage regulating device
Contact voltage regulating devices are divided into self-coupled and double-winding types, etc. They are named because they use brush contact regulation. The main feature of contact voltage regulating devices is small waveform distortion and low impedance voltage. Their capacity can also be made very large, which fundamentally overcomes the shortcomings of moving-arc voltage regulating devices and ordinary self-coupled voltage regulating devices, and is an ideal voltage regulating device.
The windings of the contact voltage regulating device are made of paper-covered wire and bare copper wire, and the brushes use specially made silver-copper alloy. During the voltage regulation process, the brush rises or drops along the winding direction to achieve continuous and stable voltage regulation, and it can basically start from zero.
Moving-arc voltage regulating device
The capacity of the moving-arc voltage regulating device should be the same as that of the test transformer. However, if the voltage regulating device is in good condition, it can be overloaded by 25%. It is best to install a third harmonic filter at the output end of the voltage regulating device to improve the voltage waveform.
Protection resistor
The high-voltage output end of the test transformer should be connected with a protection resistor to reduce the overvoltage at the outlet end of the high-voltage winding of the transformer when the test item flashes or breaks down, and to limit the short-circuit current.
The value of this protection resistor is generally 0.1Ω/V - 0.5Ω/V, and it should have sufficient heat capacity and length. The resistance value of this resistor should not exceed 30KΩ, otherwise it will cause a large voltage drop and power consumption in the circuit during normal operation. The protection resistor can be an electrolytic resistor or a wire-wound resistor. Attention should be paid to the insulation strength between the windings of the wire-wound resistor to prevent inter-winding flashover. The length of the protection resistor is selected as follows: when the test item breaks down or flashes, the protection resistor should not flash over along the surface, and its length should be able to withstand the maximum test voltage and have an appropriate margin.

Send Inquiry